The green LED will light indicating that the keypad is unlocked.
After you reconnect the power enter code 1234 immediately (when the red LED lights). Started programming can be terminated with the End key at any time.If you forgot the code you used to lock the keypad, disconnect power supply for 20 sec. Data being entering from the keypad is indicated by a red flashing LED. Setting is possible when the green LED is lit (stand by mode). Numbers and your own message into the dialer. Numbers once again and confirm your voice messageForgot your access code?Store tel. check that you selected the correct dialing method (Pulse or Tone).Ĭheck that there is a signal on the tel. If the keypad is unlocked, the calling sequence can be stopped by pressing the End key.If it does not work as you expected?. If the number is busy, the TD-110 will make 3 more attempts to call it. If the dialer makes a successful connection to a programmed number, it will not call that number again. It will then, one by one, call and play the user recorded message, for all programmed numbers. When activated, the TD-110 will immediately disengage all other devices hooked up to the phone line (telephone, fax.). Enter Mem 6 to listen to the initial voice message from the factory.SettingThe TD-110 will activate under three conditions: when its input IN1 is triggered, when the Fce key is pressed or when the remote control of a TD-110W is pressed. Loop, when used with an alarm system)After switching the power supply ON the dialer will run a self testing program and will then enter standby mode (a green LED will light). 100mA) - trigger input - connecting or disconnecting with the GND will start dialing.Ĭan be operated by Normally Closed or Normally Opened contact. If you use the dialer with an alarm system, lock the keypad after each programming.- telephone line connection (to outside line) - other devices (phone, fax.), in standby the phone line is running through the dialer - external power supply (12VDC, max. keypad unlocking: enter your code (PIN), the green LED will light. The yellow LED will turn on and the keypad is blocked against unauthorized use. Repeat the code a second time for confirmation. Keypad locking: enter Mem - and your own customized four digit code (PIN). Contact )power supplyTerminals IN OUT GND +12V IN1 TAMPER. remote controls erasing (TD-110W only) - enter Mem 9 - to erase all remote controls.phone, fax, other devicesHow the dialer workstrigger ( N.C. Both remote control buttons will have identical trigger function.TAMPER000b OUTNote: when the first remote control is taught in the learning mode, all previous remote controls are forgotten. Close the learning mode by pressing the End key. 3) one by one (pressing any button of the remote control). Learning of remote controls (TD-110W only) – after entering Mem 9 the dialer is in the remote control learning mode. Loop input (when used with alarm system)GND +12V IN1 TELEPHONE LINE INto outside line. Listening to the message: enter Mem 6 to check the recorded voice message24hr. Do not try to open the upper part of TD-110 housing during installation. After opening the terminal cover, screw in the second screw. Partly screw in the top screw and slide its head through the hole located in upper part of the dialer’s rear housing. Line signals from the built in mini speaker during the test)Fix the dialer with two screws (spacing 100mm). testing: enter Mem Fce and the dialer will call all programmed numbers once (you will hear the tel. Telephone Dialer TD-110 / TD-110W-1-MEN51206Installation. Its installation and programming is extremely easy relative to traditional dialers. The dialer can automatically call for help or to report different events. The optional model TD-110W can also be triggered with a wireless remote control. The dialer can be triggered manually or by another device connected to the TD-110 input. It can also send a numeric message to your Pager. Telephone Dialer TD-110 / TD-110W-4-Pod Skalkou 33 466 01 Jablonec nad Nisou Czech Republic Tel.: +420 483 559 999 fax: +420 483 559 993 Internet: TD-110 is an automatic dialing device that transmits a prerecorded voice message to 4 telephone numbers to an ordinary or mobile telephone system. Note: Although this product does not contain any harmful materials we suggest you to return the product to the dealer or directly to the producer after usage.